1 (844) 338-5520 Call 125 W.Victoria Street, Gardena, CA 90248 Location

AXEON® HF1-4040 Reverse Osmosis Membrane - 2500 GPD

Click Thumbnail to Zoom

AXEON® HF1-4040 Reverse Osmosis Membrane - 2500 GPD

Availability: In stock

$248.36

Scroll to Options

or

Description

AXEON® Low Pressure HF1 Series Membrane Elements are manufactured using the industry’s leading patented membrane film technology and offer reliability, high performance and deliver consistent results. They offer increased production, high rejection rates and low energy consumption by operating at low applied pressures.

  • Low Pressure
  • High Flow Capacities
  • Improved System Performance
  • Superior Quality and Cost Savings
  • Individually Tested
  • Made in the U.S.A.

AXEON® HF1 Membrane Elements are one of the industries most reliable and highest performing reverse osmosis elements. AXEON® membranes are available in all standard commercial sizes and feature a protective ABS shell. Advanced membrane technology and manufacturing processes ensure high quality and performance, allowing for improved system performance. All elements are shipped dry for an extended shelf life and easier handling. Membrane elements are 100% vacuum integrity tested and may also be ordered as individually wet tested.

Operating Limits
Membrane Type Polyamide Thin-Film pH Range, Short Term Cleaning (30 Min.) 1 - 13
Maximum Operating Temperature 113oF (45oC) Maximum Feed Water Turbidity 1 NTU
Maximum Operating Pressure 600 psi (41 bar) Maximum Feed Silt Density Index 5 SDI
Minimum Concentrate Flow Rate 5:1 Chlorine Tolerance 0 ppm
pH Range, Continuous Operation 2 - 11
Product Specification
Part Number Description Applied Pressure psi (bar) Permeate Flow Rate gpd (m3/d) Nominal Salt Rejection (%)
200374 HF1 – 2514 150 (10.34) 225 (0.85) 98.5
200375 HF1 – 2521 150 (10.34) 400 (1.51) 98.5
200376 HF1 – 2540 150 (10.34) 1000 (3.79) 98.5
200377 HF1 – 4014 150 (10.34) 600 (2.27) 98.5
200378 HF1 – 4021 150 (10.34) 1000 (3.79) 98.5
200379 HF1 – 4040 150 (10.34) 2500 (9.46) 98.5
  • Test Parameters: 550 TDS Filtered (5 Micron), De-Chlorinated, Softened City Feed Water, 77 Degrees F, 15% Permeate Recovery, 6.5 - 7.0 pH Range, at the Specified Operating Pressure. Data Taken After 30 Minutes of Operation. Maximum Pressure drop for each element is 10 psi. Minimum salt rejection is 96%. Permeate flow for individual elements may vary +/- 20%.
Dimensions inch (mm):
Description A B C D
HF1 – 2514 14 (355.6) 1.1 (27.94) 0.75 (19.05) 2.4 (60.96)
HF1 – 2521 21 (533.4) 1.1 (27.94) 0.75 (19.05) 2.4 (60.96)
HF1 – 2540 40 (1016.0) 1.1 (27.94) 0.75 (19.05) 2.4 (60.96)
HF1 – 4014 14 (355.6) 1.1 (27.94) 0.75 (19.05) 3.95 (100.3)
HF1 – 4021 21 (533.4) 1.1 (27.94) 0.75 (19.05) 3.95 (100.3)
HF1 – 4040 40 (1016.0) 1.1 (27.94) 0.75 (19.05) 3.95 (100.3)
  • Under certain conditions, the presence of free chlorine and other oxidizing agents will cause premature membrane failure. Since oxidation damage is not covered under warranty, the manufacturer recommends removing residual free chlorine by pretreatment prior to membrane exposure. Wet tested membrane elements must be kept sealed and moist when in storage. Drying out may occur and damage the membrane permanently. Prevent elements from freezing or being exposed to direct sunlight. Wet tested elements are vacuum sealed in a polyethylene bag containing 1.0% sodium meta-bisulfite and then packaged in a cardboard box. Discard the permeate for the first twenty-four hours of operation. The permeate flow (product water flow) varies with feed water temperature. For membrane warranty information, please contact the manufacturer.
    The manufacturer believes the information and data contained herein to be accurate and useful. The information and data are offered in good faith, but without guarantee, as conditions and methods of use of products are beyond the manufacturer’s control. The manufacturer assumes no liability for results obtained or damages incurred through the application of the presented information and data. It is the user’s responsibility to determine the appropriateness of these products for the user’s specific end uses

Options & Upgrades